Cosa-xentaur SF6 Purity Pro Manuel d'utilisateur

1 Optical Gas Monitor Model RK60000 COSA SF6 Purity Pro Instruction Manual COSA+XENTAUR CORPORATION LOCATIONS: 84G Horseblock Rd Ya

10 2-5. ERROR Message Display ERROR message and the meanings are as follows: Contents of Display The Meanings and

11 2-6. AIR CAL CAUTION If the temperature inside of the sensor has changed over ±10ºC from the last time the AIR CAL was performed, [CAUTION/CHECK

12 2-7. Affection on Measurement from Pressure Caution When a concentration change occurs suddenly on the RK60000, the correct reading cannot

13 An example of measurement when the pressure of the sampling point is higher than that of the atmospheric pressure: Make an inlet (a) as drawn belo

14 3. SETTING MODE (ENTER + POWER) The SETTING MODE is for “Change the Measuring Gas,” “Adjusting the time,” and “Confirming the Saved Data.” Enter

15 3-2. Adjusting the Time (SET DATE/TME) The initial position of the cursor is on YEAR. Change this with the keys and fix the setting with

16 4. MAINTENANCE 4-1. Replacing the Batteries Warning > All the C-size Alkaline batteries used in the instrument should be the

17 4-4. Frequency/Standard for Replacing Parts The frequency of the replacement mentioned below is simply standard. The life of the instrument is d

18 6. TROUBLE SHOOTING The trouble shootings mentioned below do not cover all problems, however those that occur most frequently are indicated to he

19 7. CAUTION OF USAGE The following caution items must be followed to maintain the performance and safety of the instrument. Danger >

2 Introduction Thank you for purchasing the Model RK60000. This instrument is a portable gas monitor to measure “Helium in N2,” “CH4 in air,” and ot

20 8. Definition of Terms vol%: The rate of substance occupying in some volume. The unit is indicated by percentage. ppm: The rate of substan

21 9. SPECIFICATIONS 9-1. Specifications Model Model RK60000 Detection Principle Optical Interferometric Method Display Digital Display (Measuring

22 10. MEASURING PRINCIPLE The Reflection ratio of gas mixture is determined by the kinds of composing gases as well as the mixture ratio. As long a

23 11. WARRANTY COSA INSTRUMENT CO. warrants gas alarm equipment manufactured and sold by us to be free from defects in materials and workmanship fo

24 RK60000 EACH TYPE SPECIFICATIONS (TYPE– 51 ~55)

25 TYPE-51 [FOR SOLVENT GASES (vol%)] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR CA

26 TYPE-52 [FOR SOLVENT GASES (%LEL)] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR C

27 TYPE-53 [FOR FUMIGATION GASES] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR CAL V

28 TYPE-54 [FOR GAS PURITY] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR CAL Value D

29 TYPE-55 [FOR ANAESTHETIC GASES] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR CAL

3 Index 1. PARTS AND PART FUNCTIONS…………………………………………………………………..4 2. MEASURING MODE (POWER KEY)………………………………………………………………6 2-1. Basic Display for Mea

30 TYPE-56 [FOR CALORIE MEASUREMENT] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR CA

31 TYPE-58 [FOR SF6 MEASUREMENT] Selectable Measuring Gas and Range Measuring Gas (Display Indication) Measuring Range (Minimum Digit) AIR CAL Va

32 Gas Purity Indicator for SF6 (RK60000-SF6) Simple Instructional Manual SECTION 1. POWER ON 1-1. Make sure that the change over cock (measuring ga

33 SECTION 2. ZERO ADJUSTMENT 2-1. Adjust the flow rate to be 0.2±0.04 L/min at flow meter “B” (located right on the panel). 2-2. Verify that the

34 SECTION 3. PREPARATIONS FOR GAS SAMPLING AND MEASURING 3-1. Connect the sampling tube to the gas inlet “GAS IN” on the panel and apply the sampli

35 The higher that the flow rate of meter “A” is set, the sooner its indication will be stable. Also, since the instrument has air in the internal pi

36 Operated by AC Adaptor Connect the plug of the AC adaptor to the connector. *1: Exclusive use for the model RK60000, an optional accessory. *

4 1. PARTS AND PART FUNCTIONS TOP (1) POWER key: Press this key to turn the power on until the buzzer beeps. Keep pressing the key for approxim

5 ***Explanations in the ( ) are for use during SETTING MODE. Tubing Structure (10) GAS IN Inlet for measuring gas. A specific absorption tube m

6 2. MEASURING MODE (POWER KEY) 2-1. Basic Display for Measuring Mode and Explanation Display Contents Status Gas Name and Base Gas Standard meas

7 2-2. Procedures from Power ON to Measurement 1) The power is turned on by pressing the POWER key until the buzzer beeps. The initial display (self-

8 completed, press the PUMP key and let the sample gas draw into the instrument. The color of the display will reverse while the pump is operating

9 2-3. Saving Data 2-4. Initial Display (Self-Diagnostic Display) Once the SAVE key is pres